This document describes techniques and systems of multiple-target, simultaneous beamforming for four-dimensional (4D) radar systems for efficient angle estimation in two dimensions with a high dynamic range. For example, a processor can use electromagnetic (EM) energy received by a two-dimensional (2D) array to determine first angles in a first dimension associated with one or more objects. The processor can then determine a subspace projection matrix using the first angles without an estimate of the power of noise or interference signals in the received EM energy. Using the subspace projection matrix, the processor can determine an interference-orthogonal subspace projection-based beamformer. With the interference-orthogonal subspace projection-based beamformer, the processor can determine the desired signal output from an adaptive beamformer for the EM energy and second angles corresponding to respective first angles for the objects.
G01S 13/42 - Mesure simultanée de la distance et d'autres coordonnées
G01S 7/02 - DÉTERMINATION DE LA DIRECTION PAR RADIO; RADIO-NAVIGATION; DÉTERMINATION DE LA DISTANCE OU DE LA VITESSE EN UTILISANT DES ONDES RADIO; LOCALISATION OU DÉTECTION DE LA PRÉSENCE EN UTILISANT LA RÉFLEXION OU LA RERADIATION D'ONDES RADIO; DISPOSITIONS ANALOGUES UTILISANT D'AUTRES ONDES - Détails des systèmes correspondant aux groupes , , de systèmes selon le groupe
G01S 13/931 - Radar ou systèmes analogues, spécialement adaptés pour des applications spécifiques pour prévenir les collisions de véhicules terrestres
H01Q 1/32 - Adaptation pour l'utilisation dans ou sur les véhicules routiers ou ferroviaires
A sealed electrical connector includes a seal retainer defining a plurality of wire openings, a compliant mat seal having a plurality of apertures, and a plug. The plug has a base inserted within one of the plurality of wire openings and a cylindrical post extending outwardly from the base that is inserted within one of the plurality of apertures. A method of manufacturing such a sealed electrical connector is also presented.
H01R 13/52 - Boîtiers protégés contre la poussière, les projections, les éclaboussures, l'eau ou les flammes
H01R 13/424 - Fixation de manière démontable sur un socle ou dans un boîtier composé de plusieurs pièces isolantes dont l'une au moins est flexible
H01R 43/02 - Appareils ou procédés spécialement adaptés à la fabrication, l'assemblage, l'entretien ou la réparation de connecteurs de lignes ou de collecteurs de courant ou pour relier les conducteurs électriques pour connexions soudées
Thermal management and shielding techniques for a radar device of a vehicle, the radar device having a radar transceiver circuit and a radar-transmissive radome, include a housing formed of a thermally-conductive plastic material and configured to receive and provide shield grounding to the radar transceiver circuit, and a metal layer applied to an inner surface of the housing to provide for thermal spreading of heat energy generated by the radar transceiver circuit.
G01S 7/02 - DÉTERMINATION DE LA DIRECTION PAR RADIO; RADIO-NAVIGATION; DÉTERMINATION DE LA DISTANCE OU DE LA VITESSE EN UTILISANT DES ONDES RADIO; LOCALISATION OU DÉTECTION DE LA PRÉSENCE EN UTILISANT LA RÉFLEXION OU LA RERADIATION D'ONDES RADIO; DISPOSITIONS ANALOGUES UTILISANT D'AUTRES ONDES - Détails des systèmes correspondant aux groupes , , de systèmes selon le groupe
B29C 45/14 - Moulage par injection, c. à d. en forçant un volume déterminé de matière à mouler par une buse d'injection dans un moule fermé; Appareils à cet effet en incorporant des parties ou des couches préformées, p.ex. moulage par injection autour d'inserts ou sur des objets à recouvrir
G01S 13/931 - Radar ou systèmes analogues, spécialement adaptés pour des applications spécifiques pour prévenir les collisions de véhicules terrestres
H05K 7/20 - Modifications en vue de faciliter la réfrigération, l'aération ou le chauffage
5.
THREE-DIMENSIONAL HORN AIR WAVEGUIDE ANTENNA MADE WITH FORMED AND BRAZED METAL SHEETS
A three-dimensional (3D) horn air waveguide antenna assembly and its method of manufacture include a bottom stamped metal layer defining a set of electrical connection ports and a plurality of top stamped metal layers arranged atop the bottom stamped metal layer with a brazing material deposited between each stamped metal layer, the plurality of top stamped metal layers defining a channel area proximate to the bottom stamped metal layer, a horn air waveguide antenna area that widens from a bottom portion to a top portion, and a slot area fluidly connecting the channel and horn air waveguide antenna areas.
This document describes techniques, apparatuses, and systems for movement compensation for multi-dimensional radar signal processing. A radar system receives radar signals reflected off of an object, and a two-dimension representation of the reflections is generated in the frequency domain. The two-dimensional representation illustrates attributes of the radar signals with respect to a fast-time dimension and a slow-time dimension. An energy peak within this two-dimensional representation is determined. Data associated with the energy peak, including a range and range rate, are determined from compensating the energy peak for movement of the object within a single frame. This compensation can include adjusting frequencies associated with the energy peak in the fast-time dimension and/or the slow-time dimension. The data associated with the energy peak is output to enable radar tracking with more accurate range and range rates measurements than can be output without performing movement compensation.
A connector position assurance (CPA) device includes a body and a primary lock which extends from the body in a first direction and has a primary locking mechanism at a distal end away from the body. The CPA device further includes two beam portions which are disposed on both sides of the body and extend in the first direction. At least a part of each of the two beam portions is connected to the body. The beam portion includes a secondary locking mechanism that protrudes outwards from an outer side of the beam portion.
H01R 13/639 - Moyens additionnels pour maintenir ou verrouiller les pièces de couplage entre elles après l'engagement
H01R 13/629 - Moyens additionnels pour faciliter l'engagement ou la séparation des pièces de couplage, p.ex. moyens pour aligner ou guider, leviers, pression de gaz
A cable duct assembly configured to retain an elongated cable is presented herein. The cable duct assembly includes a cover plate connected to a first sidewall and a second sidewall and a base plate pivotally connected to the first sidewall and the second sidewall. The first sidewall includes first arms that include lobe mechanisms and second arms that include rotation limiting portions.
H02G 3/00 - Installations de câbles ou de lignes électriques ou de leurs tubes de protection dans ou sur des immeubles, des structures équivalentes ou des véhicules
H02G 3/04 - Tubes ou conduits de protection, p.ex. échelles à câbles ou goulottes de câblage
An automated wire kitting system for assembling wire leads for a wired connector comprises a terminal delivery system configured to obtain a target terminal from a plurality of different types of terminals for wire leads and a crimp press comprising a plurality of dies and being configured to obtain a wire having an exposed portion where the wire's insulation has been removed, receive the target terminal from the terminal delivery system, engage a target die of the plurality of dies corresponding to a type of the target terminal, and crimp the target terminal onto the exposed portion of the wire using the target die of the plurality of dies to assemble a wire lead.
Evasive steering assist (ESA) systems and methods for a vehicle utilize a set of vehicle perception systems configured to detect an object in a path of the vehicle, a driver interface configured to receive steering input from a driver of the vehicle via a steering system of the vehicle, a set of steering sensors configured to measure a set of steering parameters, and a controller configured to determine a set of driver-specific threshold values for the set of steering parameters, compare the measured set of steering parameters and the set of driver-specific threshold values to determine whether to engage/enable an ESA feature of the vehicle, and in response to engaging/enabling the ESA feature of the vehicle, command the steering system to assist the driver in avoiding a collision with the detected object.
A lane centering system for a vehicle includes a light detection and ranging (LIDAR) system configured to (i) emit light pulses towards raised pavement markers on a road along which the vehicle is traveling and (ii) receive light pulses reflected by the raised pavement markers that collectively form LIDAR point cloud data, and a controller configured to detect a set of lane lines defining one or more lanes on the road based on the LIDAR point cloud data, based on at least the detected set of lane lines; generate a polynomial curve corresponding to a center of a lane in which the vehicle is traveling, and control steering of the vehicle based on the polynomial curve to keep the vehicle centered within the lane.
B60W 30/12 - Maintien de la trajectoire dans une voie de circulation
B60W 10/20 - Commande conjuguée de sous-ensembles de véhicule, de fonction ou de type différents comprenant la commande des systèmes de direction
G06V 20/56 - Contexte ou environnement de l’image à l’extérieur d’un véhicule à partir de capteurs embarqués
B60W 30/08 - Anticipation ou prévention de collision probable ou imminente
B60W 40/06 - Calcul ou estimation des paramètres de fonctionnement pour les systèmes d'aide à la conduite de véhicules routiers qui ne sont pas liés à la commande d'un sous-ensemble particulier liés aux conditions ambiantes liés à l'état de la route
12.
ELECTRICAL TERMINAL WITH CONNECTION TO FLEXIBLE CIRCUIT CONDUCTOR
Systems and methods for an electrical connector (e.g., of a vehicle) include a housing and a terminal at least partially disposed in the housing, defining a set of angled blade terminals, and configured to electrically connect to (i) an electrical system along a first axis and (ii) a set of exposed conductive circuit traces of a flexible circuit (FC) arranged along a second axis, wherein an acute angle is defined between the first and second axes and corresponds to the set of angled blade terminals.
H01R 12/59 - Connexions fixes pour circuits imprimés flexibles, câbles plats ou à rubans ou structures similaires
H01R 12/67 - Connexions fixes pour circuits imprimés flexibles, câbles plats ou à rubans ou structures similaires caractérisées par les bornes bornes pénétrant dans l'isolant
H01R 43/02 - Appareils ou procédés spécialement adaptés à la fabrication, l'assemblage, l'entretien ou la réparation de connecteurs de lignes ou de collecteurs de courant ou pour relier les conducteurs électriques pour connexions soudées
B60R 16/02 - Circuits électriques ou circuits de fluides spécialement adaptés aux véhicules et non prévus ailleurs; Agencement des éléments des circuits électriques ou des circuits de fluides spécialement adapté aux véhicules et non prévu ailleurs électriques
13.
SELF-ALIGNING MATE ASSURANCE MODULAR DOCKING ELECTRICAL CONNECTOR SYSTEM
Self-aligning mounting systems and methods for an electrical connectors and controllers of an electrified vehicle include a dock member configured to be fixedly attached to a frame of the electrified vehicle and to at least temporarily secure the electrical controller therein and at least one floating electrical connector floatably mateable with the dock member such that the floating electrical connector is movable by a tolerance distance amount along each of at least first and second perpendicular axes that are each parallel to the base portion of the dock member, and configured to, during securement of the electrical controller within the dock member along a third axis perpendicular to the first and second axes, electrically connect a first connection portion of the floating electrical connector to a corresponding other electrical connector, such as an inline electrical connector or an electrical connector in a bottom surface of the electrical controller housing.
H01R 13/631 - Moyens additionnels pour faciliter l'engagement ou la séparation des pièces de couplage, p.ex. moyens pour aligner ou guider, leviers, pression de gaz pour l'engagement uniquement
H01R 13/502 - Socles; Boîtiers composés de différentes pièces
H01R 13/52 - Boîtiers protégés contre la poussière, les projections, les éclaboussures, l'eau ou les flammes
H01R 43/26 - Appareils ou procédés spécialement adaptés à la fabrication, l'assemblage, l'entretien ou la réparation de connecteurs de lignes ou de collecteurs de courant ou pour relier les conducteurs électriques pour engager ou séparer les deux pièces d'un dispositif de couplage
H01R 12/77 - Dispositifs de couplage pour circuits imprimés flexibles, câbles plats ou à rubans ou structures similaires
14.
DRIVER TEMPORARY BLINDNESS EARLY WARNING AND AVOIDANCE RECOMMENDATION SYSTEM
An advanced driver assistance system (ADAS) and method for a vehicle include a light intensity detection system configured to detect a set of light density changes proximate to a face of a driver of the vehicle, a vehicle-to-everything (V2X) communication system, a global navigation satellite system (GNSS) system, and a controller configured to detect a current glare condition based on the set of detected light density changes from the light intensity detection system, share, using the V2X communication system, the detected current glare condition and the corresponding GNSS location, based on the sharing and another set of parameters, determine whether the vehicle is likely to experience a future glare condition during a future period, and in response to determining that the vehicle is likely to experience the future glare condition during the future period, at least one remedial action.
B60W 30/095 - Prévision du trajet ou de la probabilité de collision
B60W 50/00 - COMMANDE CONJUGUÉE DE PLUSIEURS SOUS-ENSEMBLES D'UN VÉHICULE, DE FONCTION OU DE TYPE DIFFÉRENTS; SYSTÈMES DE COMMANDE SPÉCIALEMENT ADAPTÉS AUX VÉHICULES HYBRIDES; SYSTÈMES D'AIDE À LA CONDUITE DE VÉHICULES ROUTIERS, NON LIÉS À LA COMMANDE D'UN SOUS-ENSEMBLE PARTICULIER - Détails des systèmes d'aide à la conduite des véhicules routiers qui ne sont pas liés à la commande d'un sous-ensemble particulier
B60W 30/12 - Maintien de la trajectoire dans une voie de circulation
A fiber enclosure with an integrated enclosure mounting system includes a base, a cover, and a clamp for securing the cover to the base. The base has an end wall with through openings extending therethrough and has a fiber management mounting frame provided on an inner side of the end wall. The mounting frame is configured to receive fiber management trays and the cover is engageable over the mounting frame and into abutment with the base and is securable to the base by the clamp to fully enclose the mounting frame and fiber management trays within a cavity formed between the cover and the base. The base also includes enclosure mounting sockets formed on an outer side surface thereof. The enclosure mounting sockets are releasably engageable with complementary shaped mounting post provided on a mounting arm to releasably secure the base to the mounting arm.
Electrical connector systems and methods create an electrical connection between a flexible circuit (FC) and a metal terminal of another connector. A reliable electrical connection is achieved with a low-cost tin contact plating, by an automatic FC to metal terminal wiping action with contact force, during the connector to FC assembly process. The connector to FC assembly process is also well suited for automated robotic assembly, which can save costs compared to manual assembly/installation.
H01R 12/77 - Dispositifs de couplage pour circuits imprimés flexibles, câbles plats ou à rubans ou structures similaires
H01R 13/52 - Boîtiers protégés contre la poussière, les projections, les éclaboussures, l'eau ou les flammes
H01R 43/26 - Appareils ou procédés spécialement adaptés à la fabrication, l'assemblage, l'entretien ou la réparation de connecteurs de lignes ou de collecteurs de courant ou pour relier les conducteurs électriques pour engager ou séparer les deux pièces d'un dispositif de couplage
This publication describes techniques and apparatuses for releasably attaching an object (e.g., a wire tray) to a substrate. Current apparatuses generally do not enable the removal of an attached wire tray from a substrate without first removing an insert from a mounting stud extending from the substrate. The disclosed techniques and apparatuses are configured to permit the removal of an attached wire tray from a substrate without first removing an insert from a mounting stud extending from the substrate.
An electromagnetic interference (EMI) shielding and thermal management system, method, and automotive radar system for an integrated circuit of a product circuit board (PCB) of a radar sensor includes a shield member disposed above the integrated circuit and extending to unpopulated areas of the PCB and configured to shield the integrated circuit from EMI and transfer heat energy generated by the integrated circuit away from the integrated circuit, and a set of pin members configured to be inserted through respective apertures defined by the shield member and the PCB and configured to transfer the heat energy from the shield member to an environment external to the PCB.
H01L 23/552 - Protection contre les radiations, p.ex. la lumière
H01L 23/367 - Refroidissement facilité par la forme du dispositif
H05K 1/18 - Circuits imprimés associés structurellement à des composants électriques non imprimés
H05K 3/30 - Assemblage de circuits imprimés avec des composants électriques, p.ex. avec une résistance
H05K 9/00 - Blindage d'appareils ou de composants contre les champs électriques ou magnétiques
H05K 7/20 - Modifications en vue de faciliter la réfrigération, l'aération ou le chauffage
G01S 7/02 - DÉTERMINATION DE LA DIRECTION PAR RADIO; RADIO-NAVIGATION; DÉTERMINATION DE LA DISTANCE OU DE LA VITESSE EN UTILISANT DES ONDES RADIO; LOCALISATION OU DÉTECTION DE LA PRÉSENCE EN UTILISANT LA RÉFLEXION OU LA RERADIATION D'ONDES RADIO; DISPOSITIONS ANALOGUES UTILISANT D'AUTRES ONDES - Détails des systèmes correspondant aux groupes , , de systèmes selon le groupe
G01S 13/931 - Radar ou systèmes analogues, spécialement adaptés pour des applications spécifiques pour prévenir les collisions de véhicules terrestres
A mounting bracket assembly for securement of elongate items, such as wires, cables, or other bundles items to a support structure. The mounting bracket assembly may include a clamp member defining a first clamp member and a second clamp member joined to the first clamp member by a hinge mechanism. The mounting bracket assembly may also include a locking mechanism, a wedge-shaped pawl having a plurality of teeth disposed within the slotted opening, and a mounting member defining a mounting aperture configured to receive an attachment feature therethrough.
H02G 3/04 - Tubes ou conduits de protection, p.ex. échelles à câbles ou goulottes de câblage
F16B 5/06 - Jonction de feuilles ou de plaques soit entre elles soit à des bandes ou barres parallèles à elles par brides ou clips
F16L 3/10 - Supports pour tuyaux, pour câbles ou pour conduits de protection, p.ex. potences, pattes de fixation, attaches, brides, colliers entourant pratiquement le tuyau, le câble ou le conduit de protection fractionnés, c. à d. à deux éléments en prise avec le tuyau, le câble ou le conduit de protection
H02G 3/32 - Installations de câbles ou de lignes sur les murs, les sols ou les plafonds utilisant des colliers de fixation
F16L 3/237 - Supports pour tuyaux, pour câbles ou pour conduits de protection, p.ex. potences, pattes de fixation, attaches, brides, colliers spécialement adaptés pour supporter un certain nombre de tuyaux parallèles séparés par un espace pour deux tuyaux
F16B 2/10 - Brides ou colliers, c. à d. dispositifs de fixation dont le serrage est effectué par des forces effectives autres que la résistance à la déformation inhérente au matériau dont est fait le dispositif externes c. à d. agissant par contraction utilisant des mâchoires sur pivot
F16L 3/127 - Supports pour tuyaux, pour câbles ou pour conduits de protection, p.ex. potences, pattes de fixation, attaches, brides, colliers entourant pratiquement le tuyau, le câble ou le conduit de protection comportant un élément entourant pratiquement le tuyau, le câble ou le conduit de protection et faisant un angle avec la surface de fixation
F16L 3/123 - Supports pour tuyaux, pour câbles ou pour conduits de protection, p.ex. potences, pattes de fixation, attaches, brides, colliers entourant pratiquement le tuyau, le câble ou le conduit de protection comportant un élément entourant pratiquement le tuyau, le câble ou le conduit de protection et s'étendant le long de la surface de fixation
A computer implemented method for compressing radar data comprises the following steps carried out by computer hardware components: acquiring radar data comprising a plurality of Doppler bins; determining which of the plurality of Doppler bins represent stationary objects; and determining compressed radar data based on the determined Doppler bins which represent stationary objects.
G01S 13/536 - Discrimination entre objets fixes et mobiles ou entre objets se déplaçant à différentes vitesses utilisant la transmission d'ondes continues non modulées, ou modulées en amplitude, en fréquence ou en phase
G01S 7/35 - DÉTERMINATION DE LA DIRECTION PAR RADIO; RADIO-NAVIGATION; DÉTERMINATION DE LA DISTANCE OU DE LA VITESSE EN UTILISANT DES ONDES RADIO; LOCALISATION OU DÉTECTION DE LA PRÉSENCE EN UTILISANT LA RÉFLEXION OU LA RERADIATION D'ONDES RADIO; DISPOSITIONS ANALOGUES UTILISANT D'AUTRES ONDES - Détails des systèmes correspondant aux groupes , , de systèmes selon le groupe - Détails de systèmes non impulsionnels
21.
Methods and Systems for Determining a Maneuver to be Executed by an Autonomous Vehicle
A computer implemented method for determining a maneuver to be executed by an autonomous vehicle comprises the following steps carried out by computer hardware components: determining a plurality of potential maneuvers; determining a subset of the potential maneuvers based on a pre-determined condition; determining a mask based on the subset; determining an output of a fully connected layer of a neural network; determining a dot product of the output of the fully connected layer and the mask; and determining the maneuver to be executed based on the dot product.
B60W 60/00 - Systèmes d’aide à la conduite spécialement adaptés aux véhicules routiers autonomes
B60W 30/095 - Prévision du trajet ou de la probabilité de collision
G06F 9/30 - Dispositions pour exécuter des instructions machines, p.ex. décodage d'instructions
G06N 3/063 - Réalisation physique, c. à d. mise en œuvre matérielle de réseaux neuronaux, de neurones ou de parties de neurone utilisant des moyens électroniques
22.
Laser transmissive compositions and related methods
Embodiments of the present disclosure include laser transmissive compositions and related methods. The laser transmissive compositions may include one or more of the following components: (a) a polyester compound; (b) a filler; (c) a non-aromatic organic nucleating agent; (d) at least one of a chain extender and a branching agent, wherein the chain extender/branching agent includes two or more reactive groups attached thereto; (e) at least one heat stabilizer; (f) at least one process stabilizer; (g) at least one lubricant; and (h) one or more further additives.
B32B 37/06 - Procédés ou dispositifs pour la stratification, p.ex. par polymérisation ou par liaison à l'aide d'ultrasons caractérisés par le procédé de chauffage
A dispensing seal includes a base seal comprised of a first material. The base seal includes at least a top surface and a bottom surface and a cavity defined therein, wherein the bottom surface includes an opening to the cavity. A second material is located within the cavity of the base seal, wherein a viscosity of the second material is less than a viscosity of the first material.
H01R 13/52 - Boîtiers protégés contre la poussière, les projections, les éclaboussures, l'eau ou les flammes
F16J 15/3284 - Joints d'étanchéité entre deux surfaces mobiles l'une par rapport à l'autre par joints élastiques, p.ex. joints toriques caractérisés par leur structure; Emploi des matériaux
24.
Anti-vibration stabilized connected system with self-rejecting ergonomic feedback mechanism
A connector assembly includes a connector body, a corresponding mating connector body, and a connection position assurance (CPA) device. The connector body includes a deflectable latching member and at least one outer detent feature located on an outer surface of the connector body. The corresponding mating connector body is configured to be removably connected with the connector body, wherein the deflectable latching member is configured to secure the connector body to the corresponding mating connector body. The CPA device is slidably positioned adjacent the connector body and moveable from a pre-stage position to a full-stage position, wherein the CPA device interacts with the at least one outer detent feature located on the outer surface of the connector body to deflect the connector body towards the corresponding mating connector body.
An electrical connector assembly includes an elongate planar terminal extending along a first longitudinal axis having a connection end configured to interconnect the terminal to a corresponding elongate planar mating terminal extending along a second axis and an attachment end configured to attach the terminal to an electrical conductor. The electrical connector assembly also includes a contact spring configured to exert a normal force between the terminal and the mating terminal when the mating terminal is arranged between the contact spring and the connection end such that second axis is parallel to the first axis or when the mating terminal is arranged between the contact spring and the connection end such that the second axis is perpendicular to the first axis.
The present disclosure enables a collection of training data suitable for training an autonomous driving system of a vehicle. A database is provided that stores predefined road scenarios, and user devices are provided with a simulation game for controlling a vehicle agent in a road scenario. A plurality of user devices, running the simulation game, play a road scenario from the database to control a vehicle agent in the simulation game with steering actions entered by individual users, which generates a human demonstration of each road scenario that is played. Several human demonstrations played on the plurality of user devices can be maintained by a demonstration database and made available as training data suitable for training an autonomous driving system of a vehicle. A large amount of training data can be automatically generated, without requiring expensive or time-consuming real-world tests to generate suitable training data manually.
B60W 60/00 - Systèmes d’aide à la conduite spécialement adaptés aux véhicules routiers autonomes
G05B 13/02 - Systèmes de commande adaptatifs, c. à d. systèmes se réglant eux-mêmes automatiquement pour obtenir un rendement optimal suivant un critère prédéterminé électriques
B60W 40/06 - Calcul ou estimation des paramètres de fonctionnement pour les systèmes d'aide à la conduite de véhicules routiers qui ne sont pas liés à la commande d'un sous-ensemble particulier liés aux conditions ambiantes liés à l'état de la route
B60W 40/08 - Calcul ou estimation des paramètres de fonctionnement pour les systèmes d'aide à la conduite de véhicules routiers qui ne sont pas liés à la commande d'un sous-ensemble particulier liés aux conducteurs ou aux passagers
B60W 50/06 - COMMANDE CONJUGUÉE DE PLUSIEURS SOUS-ENSEMBLES D'UN VÉHICULE, DE FONCTION OU DE TYPE DIFFÉRENTS; SYSTÈMES DE COMMANDE SPÉCIALEMENT ADAPTÉS AUX VÉHICULES HYBRIDES; SYSTÈMES D'AIDE À LA CONDUITE DE VÉHICULES ROUTIERS, NON LIÉS À LA COMMANDE D'UN SOUS-ENSEMBLE PARTICULIER - Détails des systèmes d'aide à la conduite des véhicules routiers qui ne sont pas liés à la commande d'un sous-ensemble particulier pour améliorer la réponse dynamique du système d'aide à la conduite, p.ex. pour améliorer la vitesse de régulation, ou éviter le dépassement de la consigne ou l'instabilité
An ejector for a molding machine includes an ejector plate and an ejector rod. The ejector plate has an opening and a distance block attached to the ejector plate. The ejector rod includes a first and a second end portion. The first end portion is in the opening of the ejector plate. The ejector rod has a first initial position relative to the ejector plate. The first end portion of the ejector rod is pushed in the direction of the ejector plate by a first force applied to the second end portion of the ejector rod. The ejector also includes a spring around the first end portion of the ejector rod and coupled to the ejector plate. The spring is configured to provide a second force to the ejector plate upon application of the first force to the second end portion of the ejector rod. There is always a gap between the first end portion of the ejector rod and the ejector plate.
A rotatable interface assembly for an electrical connector, an electrical connector, a connector system, and a method for coupling the system is presented herein. The rotatable interface assembly includes a connector component, having an electrical contact for electrically connecting electrical elements via a corresponding counter connector. The rotatable interface assembly further includes a base part and a rotatable part. The base part at least partially houses the connector component and has a securing means for being secured to a fixed counterpart. The rotatable part being configured to receive the corresponding counter connector at least partially under a specific angular orientation. The rotatable part is arranged on the base part, so as to be rotatable around a rotational axis relative to the base part. The rotatable part can be rotated around the rotational axis in a desired angular orientation that matches an orientation of a corresponding counter connector, to allow to receive the corresponding counter connector under different angular orientations, relative to the base part.
H01R 13/64 - Moyens pour empêcher, bloquer ou éviter le couplage incorrect
B60L 53/16 - Connecteurs, p.ex. fiches ou prises, spécialement adaptés pour recharger des véhicules électriques
H01R 13/506 - Socles; Boîtiers composés de différentes pièces assemblées par enclenchement réciproque des pièces
H01R 13/52 - Boîtiers protégés contre la poussière, les projections, les éclaboussures, l'eau ou les flammes
H01R 13/629 - Moyens additionnels pour faciliter l'engagement ou la séparation des pièces de couplage, p.ex. moyens pour aligner ou guider, leviers, pression de gaz
H01R 35/00 - Connecteurs de ligne flexibles ou susceptibles de rotation
29.
Electrical connector with retractable terminal-stabilizer
An electrical connector includes a mating connector in which a plurality of electrical terminals are disposed. The mating connector defines a connector shroud configured to receive a corresponding connector. The electrical connector also includes a terminal stabilizer defining a plurality of terminal apertures surrounding the electrical terminals disposed within the connector shroud. The terminal stabilizer is configured to move from a prestaged position to a seated position when the connector is inserted within the connector shroud and is further configured to move from the seated position to the prestaged position when the connector is removed from the connector shroud.
H01R 13/629 - Moyens additionnels pour faciliter l'engagement ou la séparation des pièces de couplage, p.ex. moyens pour aligner ou guider, leviers, pression de gaz
H01R 13/631 - Moyens additionnels pour faciliter l'engagement ou la séparation des pièces de couplage, p.ex. moyens pour aligner ou guider, leviers, pression de gaz pour l'engagement uniquement
H01R 13/518 - Moyens pour maintenir ou envelopper un corps isolant, p.ex. boîtier pour maintenir ou envelopper plusieurs pièces de couplage, p.ex. châssis
H01R 13/639 - Moyens additionnels pour maintenir ou verrouiller les pièces de couplage entre elles après l'engagement
30.
Injection molding a device such as a cable holder with an integrated wireless tagging foil
The disclosure relates to a method for injection-molding a device, in particular a cable tie, with an integrated wireless tag, comprising the method steps of a) putting a tagging foil with two main surfaces which are separated by an edge, into a mold cavity of an open mold, where the tagging foil is held in place by a supporting device; b) closing the mold; c) injecting an injection material into the mold cavity parts adjoining the two main surfaces of the tagging foil simultaneously and symmetrically with respect to a main extension plane of the tagging foil which is parallel to the two main surfaces of the tagging foil so as to simplify and speed up the manufacturing process of a device with an integrated wireless tag or label. The disclosure furthermore relates to a corresponding molding device as well as a corresponding device with an integrated wireless tag.
B29C 45/14 - Moulage par injection, c. à d. en forçant un volume déterminé de matière à mouler par une buse d'injection dans un moule fermé; Appareils à cet effet en incorporant des parties ou des couches préformées, p.ex. moulage par injection autour d'inserts ou sur des objets à recouvrir
Connector for automotive applications, comprising two elongated signal contacts extending generally parallel to one another, each signal contact having a first connection portion for connecting the connector to a mating connector and a second connection portion for connecting the signal contacts to respective wires of a cable, wherein a distance between center axes of the first connection portions differs from a distance between center axes of the second connection portions.
H01R 24/44 - Dispositifs de couplage en deux pièces, ou l'une des pièces qui coopèrent dans ces dispositifs, caractérisés par leur structure générale ayant des contacts disposés concentriquement ou coaxialement spécialement adaptés à la haute fréquence comprenant des moyens d'adaptation d'impédance ou des composants électriques, p.ex. des filtres ou des interrupteurs comprenant des moyens d'adaptation d'impédance
H01R 4/18 - Connexions conductrices de l'électricité entre plusieurs organes conducteurs en contact direct, c. à d. se touchant l'un l'autre; Moyens pour réaliser ou maintenir de tels contacts; Connexions conductrices de l'électricité ayant plusieurs emplacements espacés de connexion pour les conducteurs et utilisant des organes de contact pénétrant dans l'isolation effectuées uniquement par torsion, enroulage, pliage, sertissage ou autre déformation permanente par sertissage
H01R 13/516 - Moyens pour maintenir ou envelopper un corps isolant, p.ex. boîtier
H01R 24/56 - Dispositifs de couplage en deux pièces, ou l'une des pièces qui coopèrent dans ces dispositifs, caractérisés par leur structure générale ayant des contacts disposés concentriquement ou coaxialement spécialement adaptés à la haute fréquence spécialement adaptés à la forme spécifique des câbles, p.ex. câbles ondulés, câbles à paires torsadées, câbles double blindage ou câbles creux
A method for automatically mounting a connector housing with a contact part attached to an electrical line includes holding the contact part, determining an actual rotational position of the contact part, comparing the actual rotational position with a predetermined rotational position, and performing a rotational position correction thereby aligning the connector part to the connector housing. The connector housing is fixed to a holder and the contact part is inserted into a cavity of the connector housing by means of a movable gripper.
H01R 43/20 - Appareils ou procédés spécialement adaptés à la fabrication, l'assemblage, l'entretien ou la réparation de connecteurs de lignes ou de collecteurs de courant ou pour relier les conducteurs électriques pour assembler les pièces de contact avec le socle isolant, le boîtier ou le manchon ou pour les en désassembler
H01R 43/28 - Appareils ou procédés spécialement adaptés à la fabrication, l'assemblage, l'entretien ou la réparation de connecteurs de lignes ou de collecteurs de courant ou pour relier les conducteurs électriques pour traiter le fil avant sa connexion aux pièces de contact, non prévus dans les groupes
H05K 13/08 - Contrôle de la fabrication des ensembles
A wireless device charger is configured to produce an alternating magnetic field, thereby inducing an alternating electrical current within a capture coil of a personal electronic device proximate to the wireless device charger. The wireless device charger includes a source coil having a ferrite element configured to generate the alternating magnetic field, a housing formed of a thermally conductive material in thermal communication with the ferrite element, and an air movement device configured to produce a turbulent air flow across a surface of the housing flowing from an air inlet to an air outlet, thereby reducing a housing temperature.
H02J 7/02 - Circuits pour la charge ou la dépolarisation des batteries ou pour alimenter des charges par des batteries pour la charge des batteries par réseaux à courant alternatif au moyen de convertisseurs
H02J 50/80 - Circuits ou systèmes pour l'alimentation ou la distribution sans fil d'énergie électrique mettant en œuvre l’échange de données, concernant l’alimentation ou la distribution d’énergie électrique, entre les dispositifs de transmission et les dispositifs de réception
B60L 53/122 - Circuits ou procédés pour entraîner la bobine primaire, c. à d. en alimentant la bobine en énergie électrique
34.
Method of forming an electrical terminal and an electrical terminal assembly
A method of forming an electrical terminal is presented herein. The method includes the step of stamping an electrical terminal preform from a sheet of metal. The electrical terminal preform having a base plate, a plurality of contact arms radially extending from the base plate, a wire attachment feature radially extending from the base plate, and a carrier strip. The base plate defines crimp wings. The method also includes the step of bending each of the plurality of contact arms to form a socket configured to receive a mating electrical terminal.
H01R 13/20 - Broches, lames ou alvéoles conformés ou ayant une pièce séparée en vue de retenir ensemble les parties en fonctionnement
H01R 13/639 - Moyens additionnels pour maintenir ou verrouiller les pièces de couplage entre elles après l'engagement
H01R 4/58 - Connexions conductrices de l'électricité entre plusieurs organes conducteurs en contact direct, c. à d. se touchant l'un l'autre; Moyens pour réaliser ou maintenir de tels contacts; Connexions conductrices de l'électricité ayant plusieurs emplacements espacés de connexion pour les conducteurs et utilisant des organes de contact pénétrant dans l'isolation caractérisées par la forme ou le matériau des organes de contact
A battery module including a plurality of battery cells and a cell balancing system having a respective battery cell monitoring module attached to each battery cell and a module carrier having second connection means for connection of a positive terminal of the battery cell to a negative terminal of an adjacent battery cell and for an electrical connection of a negative terminal of the battery cell to a positive terminal of another adjacent battery cell. The battery cell monitoring modules are connected to one another by a balancing bus for transmitting data and electrical current. The electronic battery cell monitoring modules are connected to the positive and negative terminals of the battery cell. The module carrier has two electrical lines and an energy storage module for storing electrical energy. The energy storage module is connected to the two electrical lines to take up or output electrical energy over them.
H01M 50/502 - Interconnecteurs pour connecter les bornes des batteries adjacentes; Interconnecteurs pour connecter les cellules en dehors d'un boîtier de batterie
H01M 10/42 - Procédés ou dispositions pour assurer le fonctionnement ou l'entretien des éléments secondaires ou des demi-éléments secondaires
H01M 10/48 - Accumulateurs combinés à des dispositions pour mesurer, tester ou indiquer l'état des éléments, p.ex. le niveau ou la densité de l'électrolyte
H02J 7/00 - Circuits pour la charge ou la dépolarisation des batteries ou pour alimenter des charges par des batteries
H01M 50/20 - Montures; Boîtiers secondaires ou cadres; Bâtis, modules ou blocs; Dispositifs de suspension; Amortisseurs; Dispositifs de transport ou de manutention; Supports
A battery module for high voltage battery packs, preferably for use in vehicles, comprising a plurality of battery cells each comprising an electronic battery cell monitoring module attached to each of the battery cells, with the battery cell monitoring modules being connected to one another by a balancing bus comprising at least two electrical lines for transmitting data and electrical current, with the electronic battery cell monitoring modules being electrically connected to a positive terminal and to a negative terminal of the battery cell, with the electronic battery cell monitoring modules having a first electrical switch and a second electrical switch, with the electrical switches being configured to electrically connect the battery cells to a respective one of the two electrical lines of the balancing bus, with the battery module comprising an energy storage module for storing electrical energy, with the energy storage module being electrically connected to the two electrical lines of the balancing bus to take up or output energy over them, and with the electronic battery cell monitoring modules and the energy storage module being connected to one another by the balancing bus forming a cell balancing system.
B60L 58/22 - Procédés ou agencements de circuits pour surveiller ou commander des batteries ou des piles à combustible, spécialement adaptés pour des véhicules électriques pour la surveillance et la commande des batteries de plusieurs modules de batterie Équilibrage de la charge des modules de batterie
B60L 58/21 - Procédés ou agencements de circuits pour surveiller ou commander des batteries ou des piles à combustible, spécialement adaptés pour des véhicules électriques pour la surveillance et la commande des batteries de plusieurs modules de batterie ayant la même tension nominale
H01M 10/42 - Procédés ou dispositions pour assurer le fonctionnement ou l'entretien des éléments secondaires ou des demi-éléments secondaires
H01M 10/48 - Accumulateurs combinés à des dispositions pour mesurer, tester ou indiquer l'état des éléments, p.ex. le niveau ou la densité de l'électrolyte
37.
System for connecting wires of an electrical cable harness to an electrical connector
A system for connecting wires of an electrical cable harness to an electrical connector includes a base that defines a base plane and is configured to support a connector. The system also includes a guiding device having first and second moveable gripping portions. The first and second gripping portions cooperate to define one or more channels that extend perpendicularly to the base plane and are configured to receive one or more wire ends for insertion. An inner surface of the first gripping portion is parallel with a corresponding inner surface of the second gripping portion and an outer surface of the first gripping portion is nonparallel with a corresponding outer surface of the second gripping portion. The system further includes a robotic arm configured to move the guiding device relative to the base while the one or more channels remain perpendicular to the base plane.
H01R 43/20 - Appareils ou procédés spécialement adaptés à la fabrication, l'assemblage, l'entretien ou la réparation de connecteurs de lignes ou de collecteurs de courant ou pour relier les conducteurs électriques pour assembler les pièces de contact avec le socle isolant, le boîtier ou le manchon ou pour les en désassembler
H01R 43/28 - Appareils ou procédés spécialement adaptés à la fabrication, l'assemblage, l'entretien ou la réparation de connecteurs de lignes ou de collecteurs de courant ou pour relier les conducteurs électriques pour traiter le fil avant sa connexion aux pièces de contact, non prévus dans les groupes
H01R 43/052 - Appareils ou procédés de sertissage avec mécanisme d'alimentation en fil
H01R 43/055 - Appareils ou procédés de sertissage avec mécanisme d'alimentation en pièces de contact
38.
Mounting system for an ultrasonic-welding installation
A clamping system for an ultrasonic welding apparatus configured to clamp a contact element in the ultrasonic welding apparatus is presented. The contact element has a flat elongate shape and a welding region, a clamping region, and a contacting region arranged along a longitudinal axis. The clamping system includes two clamping units mechanically connected to the ultrasonic welding apparatus which are arranged spaced apart from one another and are moveable toward one another. Each clamping unit defines a clamping finger which is movable to extend over the clamping region. Each clamping finger has a clamping face that is configured to press on a surface of the clamping region that is located opposite an anvil of the ultrasonic welding apparatus while in a clamped state.
B23K 37/04 - Dispositifs ou procédés auxiliaires non spécialement adaptés à un procédé couvert par un seul des autres groupes principaux de la présente sous-classe pour maintenir ou mettre en position les pièces
B23K 20/10 - Soudage non électrique par percussion ou par une autre forme de pression, avec ou sans chauffage, p.ex. revêtement ou placage utilisant des vibrations, p.ex. soudage ultrasonique
H01R 43/02 - Appareils ou procédés spécialement adaptés à la fabrication, l'assemblage, l'entretien ou la réparation de connecteurs de lignes ou de collecteurs de courant ou pour relier les conducteurs électriques pour connexions soudées
An electrical connecting cable includes a plug housing, an electrical lead, a ring element, an elastic sealing element and a cap. The plug housing has a tubular lead-in region for guiding the electrical lead into the plug housing. The lead-in region is directed along a longitudinal axis of the electrical lead and has a constriction. The cap is fastened on the plug housing by retaining means. The cap has an opening for passing through the electrical lead. The ring element surrounds the electrical lead at least in part and the sealing element surrounds the electrical lead. The ring element and the sealing element are arranged between the constriction and the cap. A method of manufacturing the electrical connecting cable is also presented.
H01R 13/52 - Boîtiers protégés contre la poussière, les projections, les éclaboussures, l'eau ou les flammes
H01R 13/506 - Socles; Boîtiers composés de différentes pièces assemblées par enclenchement réciproque des pièces
H01R 13/58 - Moyens pour atténuer l'effort de tension sur le câble de connexion, p.ex. serre-câble
H01R 13/59 - Moyens pour atténuer l'effort de tension sur le câble de connexion, p.ex. serre-câble une bague filetée ou un boulon agissant dans une direction parallèle à celle du câble ou du fil
H01R 13/631 - Moyens additionnels pour faciliter l'engagement ou la séparation des pièces de couplage, p.ex. moyens pour aligner ou guider, leviers, pression de gaz pour l'engagement uniquement
H01R 43/20 - Appareils ou procédés spécialement adaptés à la fabrication, l'assemblage, l'entretien ou la réparation de connecteurs de lignes ou de collecteurs de courant ou pour relier les conducteurs électriques pour assembler les pièces de contact avec le socle isolant, le boîtier ou le manchon ou pour les en désassembler
40.
Motion-characteristic based object classification for automated vehicle
An object-classification system for an automated vehicle includes an object-detector and a controller. The object-detector may be a camera, radar, lidar or any combination thereof. The object-detector detects an object proximate to a host-vehicle. The controller is in communication with the object-detector. The controller is configured to determine a density of the object based on a motion-characteristic of the object caused by air-movement proximate to the object, and operate the host-vehicle to avoid striking the object with the host-vehicle when the density of the object is classified as dense.
G05D 1/00 - Commande de la position, du cap, de l'altitude ou de l'attitude des véhicules terrestres, aquatiques, aériens ou spatiaux, p.ex. pilote automatique
G05D 1/02 - Commande de la position ou du cap par référence à un système à deux dimensions
A wire terminal assembly is disclosed in which a conductive terminal is connected to a conductive cable core along a conductive connection interface. A coating is disposed over the conductive connection interface that is the product of a free radical polymerization reaction of a coating composition applied over the conductive connection interface, the coating composition including: (1) an oligomer comprising at least two active unsaturated bonds, (2) a monomer comprising an unsaturated bond, and (3) a compound comprising a plurality of thiol groups.
C09D 133/14 - Homopolymères ou copolymères d'esters d'esters contenant des atomes d'halogène, d'azote, de soufre ou d'oxygène en plus de l'oxygène du radical carboxyle
H01R 4/18 - Connexions conductrices de l'électricité entre plusieurs organes conducteurs en contact direct, c. à d. se touchant l'un l'autre; Moyens pour réaliser ou maintenir de tels contacts; Connexions conductrices de l'électricité ayant plusieurs emplacements espacés de connexion pour les conducteurs et utilisant des organes de contact pénétrant dans l'isolation effectuées uniquement par torsion, enroulage, pliage, sertissage ou autre déformation permanente par sertissage
H01R 11/11 - Pièces d'extrémité ou pièces de dérivation pour fils ou câbles, supportées par le fil ou le câble et munies de moyens pour faciliter la connexion électrique avec quelque autre fil, borne ou organe conducteur
An electrically conductive hybrid polymer material is described herein. The hybrid polymer material includes 0.01% to 1% by weight of carbon nanoparticles, 1% to 10% by weight of a conductive polymeric material, 1% to 20% of electrically conductive fibers having a metallic surface and 69% or more by weight of a nonconductive polymeric base material. The carbon nanoparticles may be carbon nanotubes, graphite nanoparticles, graphene nanoparticles, and/or fullerene nanoparticles. The conductive polymeric material may be an inherently conductive polymer, a radical polymers, or an electroactive polymer. The electrically conductive fibers may be stainless steel fibers, metal plated carbon fibers, or metal nanowires. The nonconductive polymeric base material may be selected from materials that are pliable at temperatures between −40° C. and 125° C. or materials that are rigid in this temperature range. The hybrid polymer material may be used to provide EMI shielding for wire cables of housings of electrical assemblies.
B60C 1/00 - Pneumatiques caractérisés par la composition chimique, la disposition ou le mélange physique de la composition
H05K 9/00 - Blindage d'appareils ou de composants contre les champs électriques ou magnétiques
C08L 101/12 - Compositions contenant des composés macromoléculaires non spécifiés caractérisées par des propriétés physiques, p.ex. anisotropie, viscosité ou conductivité électrique
H01B 1/12 - Conducteurs ou corps conducteurs caractérisés par les matériaux conducteurs utilisés; Emploi de matériaux spécifiés comme conducteurs composés principalement d'autres substances non métalliques substances organiques
H01B 1/24 - Matériau conducteur dispersé dans un matériau organique non conducteur le matériau conducteur comportant des compositions à base de carbone-silicium, du carbone ou du silicium
H01B 7/17 - Protection contre les dommages provoqués par des facteurs extérieurs, p.ex. gaines ou armatures
H01B 13/24 - Gainage; Blindage; Ecrans; Application de couches de protection d'un autre genre par extrusion
H01B 3/00 - Isolateurs ou corps isolants caractérisés par le matériau isolant; Emploi de matériaux spécifiés pour leurs propriétés isolantes ou diélectriques
A crosswalk navigation system for operating an automated vehicle in an intersection includes an intersection-detector, a pedestrian-detector, and a controller. The intersection-detector is suitable for use on a host-vehicle. The intersection-detector is used to determine when the host-vehicle is proximate to an intersection and determine when the intersection includes a cross-walk. The pedestrian-detector is suitable for use on the host-vehicle. The pedestrian-detector is used to determine a motion-vector of a pedestrian relative to the cross-walk. The controller is in communication with the intersection-detector and the pedestrian-detector. The controller is configured to determine a travel-path of the host-vehicle through the intersection, determine when the pedestrian will pass through an intersect-location where the travel-path intersects the cross-walk based on the motion-vector, and operate the host-vehicle to enter the intersection before the pedestrian passes through the intersect-location and to arrive at the intersect-location after the pedestrian passes through the intersect-location.
G01C 22/00 - Mesure de la distance parcourue sur le sol par des véhicules, des personnes, des animaux ou autres corps solides en mouvement, p.ex. en utilisant des odomètres ou en utilisant des podomètres
G05D 1/02 - Commande de la position ou du cap par référence à un système à deux dimensions
G05D 1/00 - Commande de la position, du cap, de l'altitude ou de l'attitude des véhicules terrestres, aquatiques, aériens ou spatiaux, p.ex. pilote automatique
44.
Escape-path-planning system for an automated vehicle
An escape-path-planning system to operate an automated vehicle includes an object-detector and a controller. The object-detector is suitable for use on a host-vehicle. The object-detector is used to detect an other-vehicle in an adjacent-lane next to a present-lane traveled by the host-vehicle. The controller is in communication with the object-detector. The controller is configured to, in response to a lane-change-request, determine a first-route-plan that steers the host-vehicle from the present-lane to the adjacent-lane, determine a second-route-plan that steers the host-vehicle into the present-lane, initiate the first-route-plan when a forecasted-distance between the other-vehicle and the host-vehicle is greater than a distance-threshold, and cancel the first-route-plan and select the second-route-plan when the forecasted-distance between the other-vehicle and the host-vehicle becomes less than the distance-threshold after the first-route-plan is initiated. The second-route-plan is a pre-planned escape-path that is instantly available if needed that provides a smoother travel-experience for an occupant of the host-vehicle.
G01C 21/34 - Recherche d'itinéraire; Guidage en matière d'itinéraire
G05D 1/02 - Commande de la position ou du cap par référence à un système à deux dimensions
G05D 1/00 - Commande de la position, du cap, de l'altitude ou de l'attitude des véhicules terrestres, aquatiques, aériens ou spatiaux, p.ex. pilote automatique
A wire terminal assembly is disclosed for a cable conductive core of a first metal core. A conductive terminal of a second metal is connected to the conductive cable core along a conductive connection interface. A coating is disposed over the conductive connection interface. The coating includes the free radical addition polymerizate of a coating composition of: (1) an oligomer comprising at least two active unsaturated bonds, and (2) an acrylic monomer.
H01R 4/48 - Connexions par serrage; Connexions par ressort utilisant un ressort, un clip, ou un autre organe élastique
H01R 4/18 - Connexions conductrices de l'électricité entre plusieurs organes conducteurs en contact direct, c. à d. se touchant l'un l'autre; Moyens pour réaliser ou maintenir de tels contacts; Connexions conductrices de l'électricité ayant plusieurs emplacements espacés de connexion pour les conducteurs et utilisant des organes de contact pénétrant dans l'isolation effectuées uniquement par torsion, enroulage, pliage, sertissage ou autre déformation permanente par sertissage
The invention relates to a shielded connector for a motor vehicle. The connector comprises at least one casing shielding element. The shielding element includes a cable outlet portion provided with a plurality of resilient tabs that are integral with the shielding element. The tabs include a contact zone in electrical contact with a ferrule crimped to a shielding braid of a cable. The contact zone is maintained pressed against the shielding braid by means of a removable clamping ring.
H01R 9/03 - Dispositifs de connexion conçus pour assurer le contact avec plusieurs des conducteurs d'un câble multiconducteur
H01R 13/6593 - Caractéristiques ou dispositions spécifiques de raccordement du blindage aux organes conducteurs l'organe conducteur étant un câble blindé le blindage étant composé de différentes pièces
H01R 9/05 - Dispositifs de connexion conçus pour assurer le contact avec plusieurs des conducteurs d'un câble multiconducteur pour câbles coaxiaux
H01R 13/52 - Boîtiers protégés contre la poussière, les projections, les éclaboussures, l'eau ou les flammes
H01R 13/58 - Moyens pour atténuer l'effort de tension sur le câble de connexion, p.ex. serre-câble
47.
V2X object-location verification system for automated vehicles
An object-detection system suitable for use in an automated vehicle includes a transceiver, and object-detector, and a controller. The transceiver is suitable to install on a host-vehicle. The transceiver is used to receive an indicated-location of an object proximate to the host-vehicle. The object-detector is suitable to install on the host-vehicle. The object-detector is used to detect a relative-location of the object relative to the host-vehicle. The controller is in communication with the transceiver and the object-detector. The controller determines a confirmed-location of the object relative to the host-vehicle based on the indicated-location and the relative-location. Determining the confirmed-location of the object allows for selecting from a variety of optimized algorithms to better track subsequent expected motion of the object, and reducing the risk of unnecessary or erratic action by the host-vehicle caused by hacking of the wireless-transmission or deliberate malicious content in the wireless-transmission.
A device for automatically mounting a connector-housing with a contact-part attached to an electrical line includes a holder, a movable-gripper, an alignment-station, a camera, and a control-device. The holder fixes the connector-housing. The movable-gripper holds the contact-part and inserts the contact-part into a cavity of the connector-housing. The alignment-station includes an alignment-gripper that holds the contact-part and rotates the contact-part about a rotation-axis parallel to an insertion-direction. The camera determines an actual-rotational-position of the contact-part held by the alignment-gripper in relation to the rotation-axis. The control-device compares the actual-rotational-position with a predetermined-rotational-position based on the characteristics and arrangement of the connector-housing. The control-device further controls the alignment-gripper to perform a corrective rotational movement based on the result of the comparison.
H01R 43/20 - Appareils ou procédés spécialement adaptés à la fabrication, l'assemblage, l'entretien ou la réparation de connecteurs de lignes ou de collecteurs de courant ou pour relier les conducteurs électriques pour assembler les pièces de contact avec le socle isolant, le boîtier ou le manchon ou pour les en désassembler
H01R 43/28 - Appareils ou procédés spécialement adaptés à la fabrication, l'assemblage, l'entretien ou la réparation de connecteurs de lignes ou de collecteurs de courant ou pour relier les conducteurs électriques pour traiter le fil avant sa connexion aux pièces de contact, non prévus dans les groupes
H05K 13/08 - Contrôle de la fabrication des ensembles
A method for calibrating a mounting-device used for automatically mounting a contact-part attached to an electrical line with a connector-housing includes the steps of providing the mounting-device, marking a plurality of marking-points, capturing an image of the plurality of marking-points, and determining the positions of the plurality of marking-points. The mounting-device comprises a holder for the connector-housing, a positioning-device that includes a moveable-gripper that includes a marking-device, a camera configured to capture an image of a portion of the holder, and a control unit in communication with the positioning-device, the camera, and the moveable-gripper. The control unit determines the positions of the marking-points based on the image. The positions are indicative of an actual insertion-position of the contact-part into the connector-housing by the moveable-gripper. The control unit stores the positions of the marking-points in a memory of the control unit.
H05K 3/30 - Assemblage de circuits imprimés avec des composants électriques, p.ex. avec une résistance
H01R 43/20 - Appareils ou procédés spécialement adaptés à la fabrication, l'assemblage, l'entretien ou la réparation de connecteurs de lignes ou de collecteurs de courant ou pour relier les conducteurs électriques pour assembler les pièces de contact avec le socle isolant, le boîtier ou le manchon ou pour les en désassembler
An electrical cable includes a first wire conductor separated from a second wire conductor and a compensation area proximate to, but separated from, an end portion of the cable and a method of manufacturing such an electrical cable. The first and second wire conductors are each connected to a contact element. The first and second wire conductors are separated by a first distance within the compensation area. The first and second wire conductors are separated by a second distance outside of the compensation area. The first distance is less than the second distance, thereby decreasing an impedance of the cable within the compensation area.
The invention relates to a fuse holder comprising two housing elements which, once assembled, together form a tube in which a support for a fuse is accommodated. Each of the two housing elements comprises a contact for establishing an electrical contact with a terminal of a fuse housed in the support, when the support is installed between the assembled housing elements. The support may comprise means to ensure the correct position of each contact in its respective housing element. The support may also comprise means to ensure the correct orientation of the fuse in the support. The support may also comprise means for retaining a seal ensuring sealing between the two housing elements.
H01H 85/00 - Dispositifs de protection dans lesquels le courant circule à travers un organe en matière fusible et est interrompu par déplacement de la matière fusible lorsqu'il devient excessif
H01H 85/20 - Socles pour supporter le fusible; Leurs pièces détachées
H01H 85/24 - Moyens pour empêcher l'insertion d'un fusible incorrect
H01H 85/54 - Dispositifs de protection dans lesquels le fusible est porté, tenu ou retenu par un organe intermédiaire ou auxiliaire pouvant être détaché du socle, ou utilisé comme sectionneur
52.
Electrical connector provided with a cable clamping device
The invention relates to a cable clamping device, for example for an electrical connector, comprising at least one bushing and a clamping ring. The bushing and the clamping ring both comprise an opening for the passage of a cable. A bushing has a number of bushing portions which, joined together, form a sleeve about the cable. Two flanges bear the bushing portions and are articulated to a casing so as to pivot between an unclamped position of each bushing, in which the cable can be moved, and a clamped position, in which each bushing is kept clamped to the cable by the clamping ring. Locking means keep the clamping ring in the position in which the cable is clamped by the bushing.
An electrical plug assembly including a plug housing having a first set of pins projecting from a first surface and a second set of pins projecting from an opposed second surface. The electrical plug assembly also includes an enclosure slideably attached to the plug housing. The enclosure slides to expose one set of pins while enclosing the other set of pins. The electrical plug assembly further includes a hood pivotally attached to the plug housing and slideably attached to the enclosure. The enclosure is rotatable from a first position to a second position. As the hood rotates, it slides the enclosure from a first location wherein the first set of pins is exposed to a second location wherein the second set of pins is exposed. The first set of pins conform to one technical standard, e.g. NEMA 6-20P while the second set of pins conform to another technical standard, e.g. NEMA 5-15P.
H01R 29/00 - Pièces de couplage pour coopération sélective avec une pièce complémentaire de différentes façons pour établir différents circuits, p.ex. pour la sélection de tension, pour la sélection série-parallèle
H01R 13/642 - Moyens pour empêcher, bloquer ou éviter le couplage incorrect par la position ou la forme des pièces de contact
B60L 11/18 - utilisant de l'énergie fournie par des piles primaires, des piles secondaires ou des piles à combustibles
H01R 31/06 - Pièces intermédiaires pour joindre deux pièces de couplage, p.ex. adaptateur
An electrical connector having one or more pairs of opposing contact arms extending from a body portion and configured to receive a mating connector. A spring clamp member is positioned over the opposing contact arms to increase a compressive force of the contact arms on the mating connector. The contact arms include stabilizing features to limit lateral, longitudinal, and/or rotational movement of the spring clamp member relative to the contact arms. The contact arms may be formed of a material having a high electrical connectivity and the spring clamp member may be formed of a different material having a higher relaxation temperature than the contact arm material. The mating connector may include be a male blade type terminal.
An electrical connector assembly is provided. The assembly includes a terminal, a housing, and a seal. The seal is configured to create a moisture barrier between the housing and a mating connector. The seal defines a retainer portion that cooperates with the housing to retain the terminal to the housing.
H01R 13/52 - Boîtiers protégés contre la poussière, les projections, les éclaboussures, l'eau ou les flammes
H01R 13/426 - Fixation de manière démontable par un dispositif de retenue indépendant et élastique porté par le socle ou par le boîtier, p.ex. par un collier
H01R 13/432 - Fixation de manière démontable par des moyens de verrouillage situés sur des pièces de contact élastiques par une lame élastique emboutie à enclenchement brusque derrière un épaulement du socle ou du boîtier
56.
Integrated wire cable twisting, wrapping, and testing apparatus and method of operating same
A single machine configured to manufacture a wire cable assembly including an twisted wire pair and a drain wire having a conductive tape and an insulative tape spirally wrapped about said wire pair. The machine includes a first clamp that secures an end of the wire pair and a second clamp that secures the other end of the wire pair. The second clamp rotates while the first clamp is fixed thereby twisting the wires of the wire pair one about the other. The second clamp can also rotate synchronously with the first clamp thereby rotating the wire pair without twisting. The machine also has a tape reel configured to move parallel to the clamps as they rotate, wrapping tape around the wire pair. The apparatus can be configured to apply the tapes simultaneously to electromagnetically shield and insulate the cable assembly. A method of operating the apparatus is also provided.
The present invention relates to an electromagnetic shielding device for electromagnetic shielding of a power transmitting arrangement adapted to house an electromagnetically shielded conducting element. The electromagnetic shielding device has essentially the form of a sleeve and further includes a weakened portion, which is adapted to be contracted for establishing an electrical connection between the device and the shielding of the conducting element.
H01R 13/648 - Dispositions de protection par mise à la terre ou par blindage sur les dispositifs de couplage
H01R 13/658 - Dispositions pour le blindage en haute fréquence, p.ex. protection contre les parasites électromagnétiques ou les impulsions électromagnétiques
H01R 9/05 - Dispositifs de connexion conçus pour assurer le contact avec plusieurs des conducteurs d'un câble multiconducteur pour câbles coaxiaux
H01R 43/20 - Appareils ou procédés spécialement adaptés à la fabrication, l'assemblage, l'entretien ou la réparation de connecteurs de lignes ou de collecteurs de courant ou pour relier les conducteurs électriques pour assembler les pièces de contact avec le socle isolant, le boîtier ou le manchon ou pour les en désassembler
H02G 15/068 - Boîtes, châssis ou autres structures terminales avec des moyens pour atténuer la contrainte électrique connectés au blindage du câble uniquement
H01R 13/6584 - Structure du blindage avec des moyens élastiques destinés à venir en contact avec le connecteur correspondant avec des organes élastiques conducteurs indépendants entre les organes de blindage correspondants formés par des organes élastomères conducteurs, p.ex. des joints plats ou des joints toriques
H01R 4/48 - Connexions par serrage; Connexions par ressort utilisant un ressort, un clip, ou un autre organe élastique
H01R 4/64 - Connexions entre ou avec des parties conductrices n'ayant pas au premier chef de fonction électrique, p.ex. châssis, boîtier, rail
The present invention relates to an electrical connector system. The electrical connector system includes a first connector to be mated to a corresponding counter connector and it is further adapted to be connected to a signal circuit for activating an electrical power source upon switching. As a safety feature, the connector system further includes a connector position assurance (CPA) member assigned to the first connector, which is movable, whereby an end position is not reachable if the first connector is incorrectly mated to the counter connector. The CPA member is adapted to interact with the signal circuit if placed in said end position so that it activates of the electrical power source.
H01R 29/00 - Pièces de couplage pour coopération sélective avec une pièce complémentaire de différentes façons pour établir différents circuits, p.ex. pour la sélection de tension, pour la sélection série-parallèle
B60L 3/04 - Coupure de l'alimentation en énergie en cas de fausse manœuvre
H01R 13/70 - Association structurelle avec des composants électriques incorporés avec interrupteur incorporé
H01R 13/658 - Dispositions pour le blindage en haute fréquence, p.ex. protection contre les parasites électromagnétiques ou les impulsions électromagnétiques
B60L 3/00 - Dispositifs électriques de sécurité sur véhicules propulsés électriquement; Contrôle des paramètres de fonctionnement, p.ex. de la vitesse, de la décélération ou de la consommation d’énergie
B60L 11/18 - utilisant de l'énergie fournie par des piles primaires, des piles secondaires ou des piles à combustibles
H01R 13/6593 - Caractéristiques ou dispositions spécifiques de raccordement du blindage aux organes conducteurs l'organe conducteur étant un câble blindé le blindage étant composé de différentes pièces
H01R 13/639 - Moyens additionnels pour maintenir ou verrouiller les pièces de couplage entre elles après l'engagement
H01R 13/52 - Boîtiers protégés contre la poussière, les projections, les éclaboussures, l'eau ou les flammes
H01R 13/53 - Socles ou boîtiers pour dures conditions de service; Socles ou boîtiers avec des moyens pour éviter l'effet couronne ou l'amorçage d'un arc
A method to fit a contact portion in a plug housing by a robot is presented. Steps in the method include attaching a plug housing to a holder and gripping the contact portion by a gripping device of the robot. Other steps in the method include taking at least one spatially resolved picture by at least one optical detection device such that the plug housing and the contact portion are contained in the picture, determining a respective position of the plug housing and the contact portion in the picture by a control unit of the moveable robot, calculating a robot movement by the control unit that is a function of the determined positions, and performing the calculated movement by the robot to fit the contact portion in the plug housing. An apparatus to perform the method and another method to calibrate the control unit of the robot are also presented.
H01R 9/00 - Association structurelle de plusieurs éléments de connexion électrique isolés les uns des autres, p.ex. barrettes de raccordement ou blocs de connexion; Bornes ou plots de raccordement montés sur un socle ou dans un coffret; Leurs socles
G01B 11/00 - Dispositions pour la mesure caractérisées par l'utilisation de techniques optiques
H01R 43/20 - Appareils ou procédés spécialement adaptés à la fabrication, l'assemblage, l'entretien ou la réparation de connecteurs de lignes ou de collecteurs de courant ou pour relier les conducteurs électriques pour assembler les pièces de contact avec le socle isolant, le boîtier ou le manchon ou pour les en désassembler
The present invention relates to a contact terminal for the reception of contact pins. The terminal includes a pin reception member having a box-shape made from a single piece of sheet metal, wherein two opposite walls include each at least one cut-out contact tongue being inwardly bent into the interior of the box-shape. Two other opposite walls include each a contact front portion which is inwardly bent such that the respective wall has essentially a hook-shaped cross-section to clampingly receive a contact pin.
H01R 13/187 - Broches, lames ou alvéoles ayant un ressort indépendant pour produire ou améliorer la pression de contact le ressort étant dans l'alvéole
A connector assembly is provided, and includes a first connector, a second connector, and a CPA device. The first connector has a stopper feature, a first end and a second end that generally opposes the first end. The stopper feature has a recess provided therein and a stopper surface. The second connector is received by the first connector. The second connector includes a shroud that slides over the first end of the first connector in a first direction. The CPA device is slidingly engaged with the second end of the first connector in a second direction that is generally perpendicular to the first direction. The CPA device has a flexible arm that is selectively deformable. In a pre-stage position, the flexible arm abuts against the stopper surface to restrict relative movement of the CPA device in the second direction.
A ganged electrical connection system includes an arrangement defining a plurality of receptacles. A plurality of first connectors is receivably coupled in the plurality of receptacles. A plurality of second connectors is matable to the plurality of coupled first connectors of the arrangement along mating axes. Positional mating tolerance variation associated with the plurality of second connectors in relation to the plurality of coupled first connectors manifested at the plurality of receptacles when the plurality of second connectors are mated to the plurality of coupled first connectors is absorbed by the arrangement. The plurality of the plurality of second connectors mate with the plurality of coupled first connectors in a single unimpeded, uninterrupted mating connection. A ganged electrical system for an electric-type vehicle is also presented.
H01H 13/60 - Interrupteurs ayant un organe moteur à mouvement rectiligne ou des organes adaptés pour pousser ou tirer dans une seule direction, p.ex. interrupteur à bouton-poussoir ayant un seul élément d'actionnement le contact retournant à son état initial lors de l'application suivante de la force motrice avec élément d'entraînement du contact tourné alternativement en sens opposé
66.
Method to determine a quality acceptance criterion using force signatures
A method is provided to determine a quality acceptance criterion using force signatures measured on a first and a second set of elements. The first set has no quality defect and the second set has a deliberate quality defect. Selection of an initial subset of time points is based on statistical analysis of the force data on the force signatures in the two sets. The quality acceptance criterion includes a quality threshold established using Mahalanobis Distance (MD) values and the MD values are produced from force data at a selected initial subset of time points for each element in the two sets. An output of the determined quality acceptance criterion is using the defined quality threshold to separate an element having a force signature into a group of elements having no quality defect or into a group of elements having a quality defect like the deliberate quality defect.
The present invention relates to a method for unmating an electrical connector assembly wherein the movement for unmating the first and second connectors is temporarily blocked after interlocking contacts are disconnected and before the power contacts are disconnected. The invention also relates to a connector system and a connector assembly offering such functions.
H01R 13/53 - Socles ou boîtiers pour dures conditions de service; Socles ou boîtiers avec des moyens pour éviter l'effet couronne ou l'amorçage d'un arc
An electrical connector sub-assembly including a housing having at least one electrical contact receiving area configured to receive an electrical contact; and a terminal position assurance (TPA) member located on a front section of the housing. The TPA member is laterally movable on the front section between an unlocked position and a locked position. The TPA member comprises two spaced sections configured to lock the electrical contact in the electrical contact receiving area at two spaced locations when the TPA member is moved to the locked position. This prevents unintentional withdrawal of the electrical contact from the electrical contact receiving area.
Methods of making a sealed crimp connection attaching a terminal to a wire conductor are provided. A layer of fluid conformal coating is applied to overlie a terminal and underlie at least a lead of the wire conductor upon at least the lead being received into the terminal. The terminal, the fluid layer, and at least the lead of the wire conductor are crimped to form the crimp connection. Fluid conformal coating is displaced where an abutting surface of the terminal makes contact with at least the lead of the wire conductor. The fluid conformal coating is cured to a non-fluid state. The fluid conformal coating may be formed of an acrylated urethane material that may provide an increased pull force and a low crimp resistance in the crimp connection. The crimp connection may be constructed using a manufacturing process on an automated assembly line.
H01R 43/04 - Appareils ou procédés spécialement adaptés à la fabrication, l'assemblage, l'entretien ou la réparation de connecteurs de lignes ou de collecteurs de courant ou pour relier les conducteurs électriques pour établir des connexions par déformation, p.ex. outil à plier
70.
Method of making an improved electrical connection with sealed cable core and a terminal
A method of forming a seal about an electrically conductive core of a cable having an insulative outer cover and a terminal includes the steps of providing a lead of the core extending beyond an axial edge of the insulative outer cover; spraying a conformal coating onto the lead; crimping the terminal onto the cable while the conformal coating is still wet to displace the conformal coating from between the lead and the abutting contact surfaces of the terminal and to cover and seal remaining portions of the lead not in direct contact with the terminal with the conformal coating and curing the conformal coating over the remaining portions of the lead.
H01R 43/00 - Appareils ou procédés spécialement adaptés à la fabrication, l'assemblage, l'entretien ou la réparation de connecteurs de lignes ou de collecteurs de courant ou pour relier les conducteurs électriques
71.
Electrical connector system with power and command connectors
The present relates to an electrical connector system which includes a first connector assembly having a first connector and a second connector to be coupled one to the other; a second connector assembly having a third connector and a housing contiguous to the first connector, the housing having an open connecting face for receiving within a complementary part of the third connector so as to perform a coupling one to the other. This connector system may include a movable element which is movable between two positions, i.e.: a “first position” in which it masks at least partially the open connecting face, so that it makes impossible the coupling with the third connector; a “second position” in which it does not mask the front open connecting face, so that it makes possible the coupling with the third connector; the movable element being able to be moved into the “second position” only when said first and second connectors are fully coupled together.
The invention relates to an electrical connector comprising including a housing for electrical contacts having a plugging face, and a front grid to be mounted onto the plugging face of the housing according to a plugging axis, the housing comprising including a series of locking members that lock the contacts in place, the front grid comprising: including mounting arrangements arranged for allowing the mounting of the front grid onto the housing from an open position into a closed position only if the contacts are locked in place in the housing, and at least one retractable stop member arranged for stopping the plugging of the counterpart connector with the connector as long as the front grid is not in the closed position, wherein the or each retractable stop member is arranged such that its retraction in the closed position of the front grid can be caused by a sole force exerted thereon in a direction substantially parallel to the plugging axis.
A lightweight radio/CD player for vehicular application is virtually “fastenerless” and includes a case and frontal interface formed of polymer based material that is molded to provide details to accept audio devices such as playback mechanisms (if desired) and radio receivers, as well as the circuit boards required for electrical control and display. The case and frontal interface are of composite structure, including an insert molded electrically conductive wire mesh screen that has been pre-formed to contour with the molding operation. The wire mesh provides EMC, RFI, BCI and ESD shielding and grounding of the circuit boards via exposed wire mesh pads and adjacent ground clips. The PCB architecture is bifurcated into a first board carrying common circuit components in a surface mount configuration suitable for high volume production, and a second board carrying application specific circuit components in a wave soldered stick mount configuration. The major components and subassemblies are self-fixturing during the final assembly process, eliminating the need for dedicated tools, fixtures and assembly equipment. The major components and subassemblies self-interconnect by integral guide and connection features effecting “slide lock” and “snap lock” self-interconnection. The radio architecture includes improved push buttons employing 4-bar living hinge linkage and front loaded decorative trim buttons.
The invention relates to sealable squib connectors, in particular for airbag ignition systems. The connector including a connector housing with a plug-in projection, which plug-in projection has a mating face at its distal end; a seal expansion element; and a resilient sealing ring provided at the mating face of the plug-in projection between the mating face and the seal expansion element. The seal expansion element is being movable against the mating direction towards the mating face from an open position to a closed position thereby expanding the sealing ring.
An apparatus and method of processing three-dimensional (3D) images on a multi-layer display may generate virtual depth information based on original depth information, and display 3D images having various depth values using the generated virtual depth information. Also, the apparatus and method may appropriately provide color information to each of a plurality of display layers, thereby preventing an original image from being damaged.
The present invention relates to an electrical connector, which comprises means for preventing terminals from being deformed during connection of the connector. The electrical connector of the present invention comprises: a terminal position assuring member mounted to a connector housing; and a terminal protecting plate mounted to the terminal position assuring member. The terminal protecting plate comprises a first engaging element and the terminal position assuring member comprises a second engaging compactly configured since there is no need to provide any means for mounting or retaining the terminal protecting plate to the connector housing.
H01R 13/514 - Socles; Boîtiers formés comme un bloc ou un assemblage modulaire, c. à d. composés de parties coopérantes pourvues de pièces de contact ou maintenant entre elles des pièces de contact
A socket electrical connector adapted to receive a portion of a mating plug electrical connector. The socket electrical connector includes a housing, at least two electrical contact terminals, and a contact shorting member. The housing includes a first housing member and a second housing member. The second housing member is located in the first housing member and forms a scoop proof dome having a height extending above a top side of the first hosing member. The second housing member forms at least one receiving area for receiving the portion of the mating plug electrical connector.
It is proposed a connection system for connecting a contact receptacle of a connector and a contact header of a counterpart connector. The connection system includes locking means for maintaining the contact receptacle in an intermediate position into a frame of the connector, and unlocking means for releasing the contact receptacle from its intermediate position.
A filtered electrical connection header assembly for an electrical device, and methods for assembling a filtered connection header assembly for an electrical device, are disclosed. An electrical connection header may include a housing for an electrical circuit and a connection header assembly secured to the housing that includes a plurality of electrical pins. The pins may each include a first portion, and a second portion oriented generally orthogonal to the first portion. The second portions of the pins extend into the housing to contact the electrical circuit. A forward end of a connector shroud may receive a pin stabilizer having a plurality of apertures that receive the first portion of the pins for engagement with a mating connector. The electrical connection header may further include a filter assembly configured to filter a signal transmitted though the pins that is secured to the external surface of the housing.
H01R 12/00 - Association structurelle de plusieurs éléments de connexion électrique isolés les uns des autres, spécialement conçue pour des circuits imprimés, p.ex. des cartes de circuit imprimé [PCB], des câbles plats ou à ruban ou des structures similaires géné; Dispositifs de couplage spécialement conçus pour des circuits imprimés, des câbles plats ou à ruban ou des structures similaires généralement planes; Bornes spécialement conçues pour établir le contact avec, ou pour être insérées dans des circuits imprimés, des câbles plats ou à ruban ou des structures similaires généralement planes
A filtering ferrite block assembly for squib system electrical conductors including a first ferrite block including first conductor channels; and a second ferrite block including second conductor channels. The second ferrite block is adapted to be connected to the first ferrite block with portions of the electrical conductors therebetween. The electrical conductors extend through the first and second conductor channels between the two ferrite blocks.
A plastic component is attached to a mounting structure by a fastener that extends at least into a mounting hole in the plastic component. The mounting hole is located near an edge corner of a cantilevered mounting tab that forms part of the plastic component. The mounting tab comprises a generally flat plate that has a depending flange that extends around a rounded corner near which the mounting hole is located and a depending sleeve that is contiguous with the mounting hole. The mounting tab has a break away portion so that the plastic component can be removed for recycling easily. Three variations of the breakaway portion are disclosed.
An electrical connector housing including a base; and a cover. The cover is adapted to be connected to the base to capture at least one electrical connector component in the base. The cover includes a first section and a second section. The second section is movably connected to the first section by a connection. The second section is movable between an open position relative to the base and a closed position. The connection includes a detent latching system for latching the second section in the open position to allow access to a location inside the base.
A wire bundle routing assembly for routing and at least partially enclosing and sealing a wire bundle between a a vehicle door frame and a vehicle door body. A door mounting base is slidably receivable in a slot formed in a front wall of a door body and includes a wire bundle through-hole. A door mounting base cover at least partially encloses and holds the wire bundle against an inner side of the door mounting base when the cover is installed over the inner side of the door mounting base. A base slide track detent surface on the door mounting base engages a corresponding cover slide track detent surface on the cover and guides the cover as the cover is slid into an installed position on the mounting base.
An electrical connector housing including a base; and a cover. The cover is adapted to be connected to the base to capture at least one electrical connector component in the base. The cover includes a first section and a second section. The second section is movably connected to the first section by a connection. The second section is movable between an open position relative to the base and a closed position. The connection includes a detent latching system for latching the second section in the open position to allow access to a location inside the base.
A socket electrical connector adapted to receive a portion of a mating plug electrical connector. The socket electrical connector includes a housing, at least two electrical contact terminals, and a contact shorting member. The housing includes a first housing member and a second housing member. The second housing member is located in the first housing member and forms a scoop proof dome having a height extending above a top side of the first hosing member. The second housing member forms at least one receiving area for receiving the portion of the mating plug electrical connector. The electrical contact terminals are connected to the first housing member and extend into the at least one receiving area of the second housing member. The contact shorting member is mounted on the second housing member and contacts the electrical contacts.
An electrical connector has a CPA plug (connector position assurance plug) for assuring that the electrical connector is properly connected to a mating electrical connector. The electrical connector includes a right-angled connector body having a plurality of longitudinal channels that open into an axial shroud that plugs into a socket of the mating connector in the axial direction, and a plurality of right angled terminals that are disposed in the plurality of longitudinal channels respectively with their respective contacts disposed in the axial shroud. The axial shroud has a cover at one end and the CPA plug is attached to the cover for movement between a prestaged position and a final locked position assuring that the electrical connector is properly connected to the mating electrical connector. Three embodiments are disclosed.
Disclosed herein is an electrical connector. The electrical connector includes a user contact member, a housing, a plurality of electrical contacts, and a slide. The user contact member has a first extending arm. The first extending arm includes a first cam projection. The housing has a first arm slot. The first arm slot receives the first extending arm. The plurality of electrical contacts are mounted in the housing. The slide is positioned between the first extending arm and the second housing. The slide includes a first cam slot and a second cam slot. The first cam slot receives the first cam projection. The second cam slot is adapted to receive a second cam projection of a mating electrical connector. The electrical connector is configured to receive at least one wire between the housing and the user contact member.
A detecting device for a vehicle and method thereof is provided. The device includes a first infrared detector, a second infared detector, and a controller. The first infrared detector is configured to repeatedly measure a temperature of a first target area by receiving infrared radiation of the first target area over a sampling period. The second infrared detector is configured to repeatedly measure a temperature of a second target area by receiving infrared radiation of the second target area over the sampling period. The controller is configured to receive and store the plurality of first and second signals, wherein the controller repeatedly compares a plurality of correlation values to a predetermined tolerance range above a minimum threshold value, wherein the correlation values are determined by repeatedly comparing a plurality of time delayed signals of the second plurality of signals to a real time signal of the plurality of first signals.
A wireless audio distribution system may include a wireless transmitter, responsive to a plurality of audio input channels, for transmitting an encoded digital bitstream serially combining each of the audio input channels with control data a receiver responsive to the transmitted encoded digital bitstream for decoding a preselected one of the plurality of the audio input channels from the digital bitstream for reproduction and at least one speaker for reproducing the preselected audio input channel in accordance with the control data. A wireless speaker system may include a receiver, responsive to a wirelessly transmitted, encoded digital bitstream serially combining each of a plurality of the audio input channels with control data disbursed therein, for decoding a preselected one of said audio input channels and a speaker system responsive to the receiver for reproducing the decoded, preselected audio input channel.
An intermittent contact connector device including a frame having a first frame section movably connected to a second frame section; two electrical contacts connected to the second frame section, and an electrical shorting member connected to the first frame section. At least one of the contacts is an insulation displacement contact (IDC) member. The shorting member is adapted to contact the two electrical contacts to thereby electrically connect the two electrical contacts to each other when the first frame section is moved towards the second frame section.
H01H 13/52 - Interrupteurs ayant un organe moteur à mouvement rectiligne ou des organes adaptés pour pousser ou tirer dans une seule direction, p.ex. interrupteur à bouton-poussoir ayant un seul élément d'actionnement le contact retournant immédiatement à son état initial après suppression de la force motrice, p.ex. bouton-poussoir de sonnerie
A vehicle air bag electrical system including an air bag control module; electrical conductors connected to the control module; an electrical connector connected to the electrical conductors; and a filter circuit coupled to the electrical conductors. The filter circuit includes a plurality of capacitors provided as a module. The electrical connector is adapted to be connected to an air bag gas initiator.
An optical information processing circuit assembly includes an optically transmissive substrate and a resiliently compressible circuit member affixed to the substrate and defining an opening therethrough with a number of leads disposed about the opening. An integrated imaging circuit defines a corresponding number of pads wherein the pads align with and electrically contact the leads. An optically transmissive medium may be disposed between and in contact with the substrate and the integrated imaging circuit to allow light transmission therethrough from the substrate to the imaging circuit. In one embodiment, resilient bumps are provided between the integrated imaging circuit and the resiliently compressible circuit member to form the electrical connection therebetween. Alternatively, solder bumps may replace the resilient bumps. Additional circuit components may be similarly mounted to the resiliently compressible circuit member to complete the assembly.
G02B 6/12 - OPTIQUE ÉLÉMENTS, SYSTÈMES OU APPAREILS OPTIQUES - Détails de structure de dispositions comprenant des guides de lumière et d'autres éléments optiques, p.ex. des moyens de couplage du type guide d'ondes optiques du genre à circuit intégré
93.
Solid-oxide fuel cell assembly having a convectively vented structural enclosure
In a solid-oxide fuel cell system, the fuel cell stacks, the fuel reformer, tail gas combuster, heat exchangers, and fuel/air manifold, are contained in a “hot zone” within a thermal enclosure. A separate and larger structural enclosure surrounds the thermal enclosure, defining a “cool zone” outside the thermal enclosure for incorporation of “cool” components such as the air supply system and the electronic control system. To prevent unwanted temperature rise in the cool zone during shutdown, from residual heat escaping from the hot zone through the thermal enclosure, the structural enclosure is provided with vents through the lower and upper walls thereof to permit thermal convective circulation of air through the enclosure. The vents are baffled to prevent entry of splash and other contaminants, and the lower vent is provided with a float valve to prevent flooding of the enclosure in event of immersion of the SOFC system.
H01M 8/04 - Dispositions auxiliaires, p.ex. pour la commande de la pression ou pour la circulation des fluides
H01M 8/12 - PROCÉDÉS OU MOYENS POUR LA CONVERSION DIRECTE DE L'ÉNERGIE CHIMIQUE EN ÉNERGIE ÉLECTRIQUE, p.ex. BATTERIES Éléments à combustible; Leur fabrication Éléments à combustible avec électrolytes solides fonctionnant à haute température, p.ex. avec un électrolyte en ZrO2 stabilisé
H01M 8/06 - Combinaison d’éléments à combustible avec des moyens de production de réactifs ou pour le traitement de résidus
B60L 11/18 - utilisant de l'énergie fournie par des piles primaires, des piles secondaires ou des piles à combustibles
94.
Solid-oxide fuel cell system having a fuel combustor to pre-heat reformer on start-up
In a solid-oxide fuel cell system, a catalytic reformer unit provides reformate fuel for use by the cells in generating electricity. Both the reformer and the fuel cells require elevated temperatures for satisfactory operation. The reformer unit is provided with a combustion chamber and igniter ahead of the catalytic reformer plates such that, during start-up, fuel/air mixture normally destined for reformation may be ignited in the combustion chamber to provide a hot combustion exhaust which is fed through the catalytic reformer and the anode reformate flow spaces to assist in rapidly bringing the fuel cell system to operating temperature.
In a solid-oxide fuel cell system, an integrated air supply system provides oxygen for the fuel cell cathode reaction via a first air flow through a heat exchanger and a second air flow bypassing the heat exchanger, at least one of the first and second flows being throttled by a control valve responsive to a fuel cell control system, the flows subsequently being combined to provide air to the cathodes at a desired temperature.
A solid-oxide fuel cell system having a compact, highly space-efficient basal manifold for conveying high temperature air, exhaust, and hydrogen-rich reformate fuel to and from the core components of the system. The manifold is a three-dimensional assembly of plates and partitioned elements which are easily and inexpensively formed. When assembled, the manifold comprises a network of passageways which allow for the mounting, close-coupling, and integration of critical fuel cell system components, including heat exchangers, a tail gas combustor and fuel reformer, solid-oxide fuel cell stacks, check valves, and oxygen scavengers.
H01M 8/02 - PROCÉDÉS OU MOYENS POUR LA CONVERSION DIRECTE DE L'ÉNERGIE CHIMIQUE EN ÉNERGIE ÉLECTRIQUE, p.ex. BATTERIES Éléments à combustible; Leur fabrication - Détails
H01M 8/04 - Dispositions auxiliaires, p.ex. pour la commande de la pression ou pour la circulation des fluides
H01M 8/06 - Combinaison d’éléments à combustible avec des moyens de production de réactifs ou pour le traitement de résidus
B60L 11/18 - utilisant de l'énergie fournie par des piles primaires, des piles secondaires ou des piles à combustibles
97.
Method and apparatus for fuel/air preparation in a fuel cell
A fast start-up catalytic reformer for producing hydrogen-rich reformate from hydrocarbon fuel includes a reactor having an inlet for receiving a flow of fuel and a flow of air, a reforming catalyst disposed within a reforming chamber in the reactor, and an outlet for discharging the produced reformate stream. An ignition device within the reactor tube ignites a first lean mixture in combustion mode to generate exhaust gases to warm the catalyst which also warms the wall of the reactor adjacent the catalyst. The reactor then switches over to a rich fuel/air mixture during reforming mode. A jacket concentrically surrounds the reactor, defining a mixing chamber therebetween which communicates with the reforming chamber via openings in the wall of the reactor. Fuel entering the reformer in combustion mode is injected directly into the reforming chamber to provide rapid warming of the catalyst. Fuel entering the reformer in reforming mode is sprayed onto the outside of the reactor in the mixing chamber, preferably in the heated region of the tube for very rapid vaporization.
C10K 3/06 - Modification de la composition chimique des gaz combustibles contenant l'oxyde de carbone en vue de produire un carburant amélioré, p.ex. un carburant de pouvoir calorifique différent qui peut ne pas contenir d'oxyde de carbone par mélange avec des gaz
C10J 3/00 - Production de gaz contenant de l'oxyde de carbone et de l'hydrogène, p.ex. du gaz de synthèse ou du gaz de ville, à partir de matières carbonées solides par des procédés d'oxydation partielle faisant intervenir de l'oxygène ou de la vapeur
brevets
